PLAYBUS - Domestic range Modular devices

ACCESSORIES SUPPLIED: GW30007: 2 keys. The key can be extracted in both positions. Spare keys: GW20901. Backlit items are supplied without lamp. They use miniature lamp units.

ACCESSORIES SUPPLIED: backlit items are supplied without lamp. They use miniature lamp units.

CHARACTERISTICS: three standing positions. Both contacts are open in the central position (OFF).
APPLICATIONS: command of circuits requiring an interlock (e.g. operating motorised devices with direction reversal). 2-user selective control.

CHARACTERISTICS: GW30033: independent push-buttons that can also be activated simultaneously. GW30034: three-way push-button with interlock.
Both contacts are open in the central position (OFF).
APPLICATIONS: GW30034: impulse activation of motorised devices with direction reversal (e.g. roller shutters, curtains, etc.).
ACCESSORIES SUPPLIED: GW30031 cord in insulating material, 150cm long, with knob. GW30032 supplied with 2 keys. Spare keys: GW30912.
Backlit items are supplied without lamp. They use miniature lamp units.

APPLICATIONS: in installations on 3 gang plates, the dimensions of the device (only 2 modules) allow another 1 module device to be inserted.
ACCESSORIES SUPPLIED: supplied without lamp.

The PLAYBUS modular system allows the use of interchangeable buttons 25x45 mm to substitute the standard keys supplied on control devices.
CHARACTERISTICS: backlit buttons excluding items GW30041 - GW30056.

The PLAYBUS modular system allows the use of interchangeable buttons 25x22.5 mm to replace the standard keys supplied on control devices GW30033.
CHARACTERISTICS: backlit buttons.

APPLICATIONS: in addition to their normal use, they permit installing signal socket-outlets, microswitches and LEDs after appropriate drilling/preparation.
In addition, it is possible to apply the temperature sensor GW30703 using the special double-sided adhesive.
ACCESSORIES SUPPLIED: GW30905, fastner cable fastener device.

CHARACTERISTICS: adjustment of the intervention duration 15 sec - 10 min. Light sensitive threshold adjustment - min. 10 lux - max. inhibited. Sensor with fixed lens. Suitable for commanding halogen lamps/resistive loads: 700 W, incandescent lamps: 450 W, low voltage halogen lamps (12 V) controlled by toroidal or electronic transformers: 450 W, uncompensated fluorescent lamps: 2x58 W, motors and gear motors: 400 VA. Not suitable for compensated fluorescent lamps, for discharge lamps and for all loads not indicated that must be commanded using a support relay.
APPLICATIONS: Energy-saving: command of the lighting of rooms and areas only when people pass through.
Comfort and safety: automatic command of circuits without needing to activate one-way switches.
NOTES: do not install the product in watertight plates: the lid membrane does not allow the detector lens to work correctly.

CHARACTERISTICS: suitable for commanding incandescent/halogen lamps: 800 W, fluorescent tubes with electronic ballast: 400 W, fluorescent tubes with electromechanical ballast: 360 W, compact fluorescent lamps (CFL): 200 W, LED lamps (230V ac): 200 W, low voltage halogen or LED lamps with electronic ballast: 200 W, low voltage halogen or LED lamps with electromechanical ballast: 400 W.
APPLICATIONS: command of lighting devices from several points, via push-buttons. Start/stop control of motors (extractors, air agitators, etc.).

APPLICATIONS: as an auxiliary element for commanding special loads, for remote signalling, for electric separation of command circuits from utilisation circuits.

CHARACTERISTICS: with safety shields.

CHARACTERISTICS: with safety shields.

CHARACTERISTICS: with safety shields.

CHARACTERISTICS: with safety shields.

CHARACTERISTICS: with safety shields.

CHARACTERISTICS: with safety shields.

CHARACTERISTICS: with safety shields.

CHARACTERISTICS: with safety shields.
NOTES: given the size of the plugs, it is not possible to install two or more socket-outlets side-by-side.

CHARACTERISTICS: with safety shields.

CHARACTERISTICS: with safety shields.

CHARACTERISTICS: GW30311 permits carrying a remote power supply voltage/current and/or control signals towards the user port (max 24 V - 500 mA). GW20277 in combination with feedthrough socket-outlets allows you to make terminal socket-outlets.
APPLICATIONS: Socket-outlets suitable for return channel.
NOTES: the TV-SAT 5 dB GW30316 coaxial socket-outlet is defined with conditioned use, it is a special through socket-outlet and as such must be used, with the only difference that the user door (socket-outlet towards the user device) must always be closed with a load of 75 Ohm (TV, VCR, SAT receiver or 75-Ohm termination).

CHARACTERISTICS: GW30301 permits carrying a remote power supply voltage/current and/or control signals towards the user port (max 24 V - 500 mA). GW20277 in combination with feedthrough socket-outlets allows you to make terminal socket-outlets.
APPLICATIONS: Socket-outlets suitable for return channel.
NOTES: the TV 5 dB GW30306 coaxial socket-outlet is defined with conditioned use, it is a special through socket-outlet and as such must be used, with the only difference that the user door (socket-outlet towards the user device) must always be closed with a load of 75 Ohm (TV, VCR, SAT receiver or 75-Ohm termination).

APPLICATIONS: telephone, telefax, modem.

APPLICATIONS: LANs up to 100MHz (e.g. Ethernet, Token Ring networks) for cat. 5e.
LANs up to 250MHz (e.g. Videoconference systems, CCTV) for cat. 6.
ACCESSORIES SUPPLIED: circuit identification label.

ACCESSORIES SUPPLIED: circuit identification labels.
NOTES: with regard to the technological developments and dimensional variants introduced by connector manufacturers, you are advised to check in advance the full compatibility between the connector and the empty Gewiss container.

CHARACTERISTICS: equipped with inhibition selector on the front. Use battery pack 4.8 V 40 mAh.

CHARACTERISTICS: supplied without lamp. They use S6x31 mm and S6.3x28 mm cartridge lamps (max 2 W).
NOTES: the meaning of the diffusers refers to the recommendations of standard EN60073 with regard to the use of the colours in indicator lights.

CHARACTERISTICS: for intermittent use (5 sec. ON / 15 sec. OFF).

CHARACTERISTICS: for intermittent use (5 sec. ON / 15 sec. OFF).

CHARACTERISTICS: frequency 50/60 Hz. Equipped with orange signalling LED.
NOTES: the installation of more than one product side-by-side in a single container is not permitted. To avoid overheating, insert a blanking module between two electronic devices. If installing two regulators in the same box, the maximum loads that can be commanded by each regulator must be reduced by 50%.

CHARACTERISTICS: frequency 50/60 Hz. Equipped with orange signalling LED. GW30403: resistive load 110V AC 100-500 W; inductive load 110V AC 20-150 VA.
GW30403 compliance with the EMC directive is only guaranteed by connecting the regulator to an LC filter with the following characteristics: L=1mH - 5A, C=0.15uF - 275V X2, according to the documentation provided with the product. Item designated solely for export to a limited number of countries outside the European Union or countries applying to become part of the European Free Trade Area. Contact Gewiss Customer Service to check the product meets the regulations of the country concerned before importing it. GW30404: resistive load 110V AC 20-150 W; inductive load 110V AC 20-150 VA.
NOTES: the installation of more than one product side-by-side in a single container is not permitted. To avoid overheating, insert a blanking module between two electronic devices. If installing two regulators in the same box, the maximum loads that can be commanded by each regulator must be reduced by 50%.

CHARACTERISTICS: frequency 50/60 Hz. Equipped with orange signalling LED.
ACCESSORIES SUPPLIED: quick fuse Ø 5x20 mm - 2.5 A.
NOTES: the installation of more than one product side-by-side in a single container is not permitted.
To avoid overheating, insert a blanking module between two electronic devices. If installing two regulators in the same box, the maximum loads that can be commanded by each regulator must be reduced by 50%.

CHARACTERISTICS: self-protected against overloading and short-circuiting. Frequency 50 Hz. Equipped with red signalling LED.
NOTES: the installation of more than one product side-by-side in a single container is not permitted.
To avoid overheating, insert a blanking module between two electronic devices. If installing two regulators in the same box, the maximum loads that can be commanded by each regulator must be reduced by 50%.

CHARACTERISTICS: with rechargeable buffer battery to guarantee the updating of the calendar (date, day, time) in the event of a blackout.
Serial input for connecting the GW90821 GSM remote control.

CHARACTERISTICS: with buffer battery (30 days reserve charge). Input for 1 external probe GW30703 available as accessory, to display the temperature of another environment.
NOTES: customizable temperature setpoints: frost, comfort and night.

CHARACTERISTICS: cable extendable up to max 50m (min section 2x0.35mm²).
APPLICATIONS: can be used in bedrooms, bathrooms, kitchens, as a supplementary indoor probe, or outside the home.
ACCESSORIES SUPPLIED: expandable wall plug with screws and double-sided adhesive for wall or smooth surfaces mounting (or on a blanking module).

CHARACTERISTICS: relay output for the automatic command of the gas interception solenoid valve (manual reset) GW30522. Sound intensity: 85dB at 1m.

CHARACTERISTICS: relay output for the automatic command of the gas interception solenoid valve (manual reset) GW30522. Sound intensity: 85dB at 1m.

APPLICATIONS: to be used for powering LPG detectors (GW10711, GW12711, GW14711, GW20868, GW21868, GW30520), methane detectors (GW10712, GW12712, GW14712, GW20867, GW21867, GW30519); Thermo ICE WiFi (GW16972CB, GW16972CN, GW16972CT) and KNX/Easy (GW16974CB, GW16974CN, GW16974CT) thermostats.

CHARACTERISTICS: supplied without a badge.
APPLICATIONS: activation of circuits and services in hotel rooms (e.g. lights, air-conditioner, fridge-bar), indication of room occupied (with badge inserted).

CHARACTERISTICS: the socket-outlet is equipped with a self-protection device against overloading.
The output voltage should be selected correctly, consulting the rating of the user device before inserting the plug.
The relevant indicator LED allows the chosen voltage to be clearly seen.

APPLICATIONS: miniature lamps are mounted on all control devices fitted for luminous signalling.

NOTES: the cartridge lamps are mounted on the stair riser, on the single indicator lamps and on the push-buttons with a name plate.